Gefen EXT-HDMI1.3-CAT6-8X Manuel d'utilisateur

www.gefen.com®®EXT-HDMI1.3-CAT6-8XUser Manual

6SENDER UNIT LAYOUT25 736814Back

7SENDER UNIT DESCRIPTIONSBack1RS-232 Serial Port (Input)The 8x8 Matrix may be switched remotely using serial communications with anyoffi ce computer or

8RECEIVER UNIT LAYOUTFront31542

9RECEIVER UNIT DESCRIPTIONSFront1Control Buttons (1 - 8)When connected to any 8x8 Matrix for HDMI, these remote buttons on theReceiver unit can switch

10RECEIVER UNIT LAYOUTBack365421

11RECEIVER UNIT DESCRIPTIONSBack1Control Buttons (1 - 8)When connected to any 8x8 Matrix for HDMI, these remote buttons on theReceiver unit can switch

121 Activity IndicatorThis LED will be activated momentarily each time a button is pressed.2 Input Source Selection Buttons (1 - 8)These buttons are

13RMT-8IR REMOTE INSTALLATIONInstalling the RMT-8IR Battery1.Remove the battery cover on the back of the IR Remote Control unit.2. Insert the include

14Setting the IR Remote Channel on the RMT-8IRIn the event that IR commands from other remote controls confl ict with thesupplied RMT-8IR Remote, chang

15CONNECTING AND OPERATING THE8X CAT6 EXTENDER FOR HDMIHow to Connect the 8x CAT6 Extender for HDMI(Matrix Mode)1. Using any 8x8 Matrix for HDMI as a

16How to Operate the 8x CAT6 Extender for HDMI(using an 8x8 Matrix)The front panel of each Receiver unit for the 8x CAT6 Extender for HDMI contains a

17How to Connect the 8x CAT6 Extender for HDMI with RS-232 control tothe 8x8 Matrix for HDMI and to the controlled device1. Follow steps 1 - 6 on How

18How to Connect the 8x CAT6 Extender for HDMI(Stand-alone Mode)The 8x CAT6 Extender for HDMI is dependent upon an external 8x8 Matrix to manage all t

19Routing Sources using the Optional RMT-8IR Remote Unit(Matrix Mode)There are a total of 8 buttons on the RMT-8IR remote, which represent each of the

20How to Operate the 8x CAT6 Extender for HDMI(Stand-alone Mode)When the 8x CAT6 Extender for HDMI is used without an 8x8 Matrix, it can only be used

21How to Equalize the 8x CAT6 Extender for HDMI(Matrix Mode / Stand-alone Mode)The 8x CAT6 Extender for HDMI Receiver unit has an equalization trimpot

22Controlling the Receiver Unit using RS-232(Matrix Mode)1.Prepare the Receiver unit by connecting an RS-232 cable from the computer or other controll

23Default settings for DIP switchesDIP SwitchPosition1OFF2OFF3OFF4OFFDIP Switch Location(Matrix Mode / Stand-alone Mode)On the bottom of each Receiver

24DIP SWITCH CONFIGURATIONDIP Switches(Matrix Mode / Stand-alone Mode)DIP 1 - EDID Management• OFF - Local EDIDWhen Local EDID mode is used, the EDID

25543219876123456789Only Pins 2 (RX), 3 (TX), and 5 (Ground) are used on the RS-232 serial interfaceRS-232 SERIAL CONTROL INTERFACERS-232 SettingsBits

ASKING FOR ASSISTANCERev B5Technical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM

26RS-232 SERIAL FUNCTIONS - SENDER UNITFunctions SyntaxThe syntax for each function is always the same:#Character as the start fl ag → Function name →

27RS-232 SERIAL FUNCTIONS - SENDER UNIT#LOEDIDTOLO FunctionThe #LOEDIDTOLO function loads the specifi ed EDID fi le to a specifi ed localinput via RS-232

28RS-232 SERIAL FUNCTIONS - SENDER UNITIP Confi guration - Sender UnitFunctionDescription#SIPADDSpecifi es a new IP address#SNETMASKSpecifi es a new net

29RS-232 SERIAL FUNCTIONS - SENDER UNIT#SNETMASK FunctionThe #SNETMASK function specifi es a new net mask.Syntaxy:#SNETMASK param1 param2 param3 param4

30RS-232 SERIAL FUNCTIONS - SENDER UNIT#SPORT FunctionSpecifi es a new port.Syntaxy:#SPORT param1Parameters:param1 Port [0 - 255]Notes:A reboot is

31RS-232 SERIAL FUNCTIONS - SENDER UNITGeneral FunctionsFunctionDescription#ACTIVEBOLOEnables the boot loader#BLASTERSets the Receiver unit blaster mo

32RS-232 SERIAL FUNCTIONS - SENDER UNIT#BLASTER FunctionThe #BLASTER function sets the Receiver Unit blaster mode.Syntaxy:#BLASTER param1 param2Parame

33RS-232 SERIAL FUNCTIONS - SENDER UNIT#CTARGET FunctionThe #CTARGET function defi nes how to send routing commands to the Matrix.Syntaxy:#CTARGET para

34RS-232 SERIAL FUNCTIONS - SENDER UNIT#HPDMODE FunctionThe #HPDMODE function sets HPD to low (OFF) or high (ON) on the HDMIinputs.Syntaxy:#HPDMODE pa

35RS-232 SERIAL FUNCTIONS - SENDER UNIT#MASKOUT FunctionThe #MASKOUT function allows blanking of selected outputs.Syntaxy:#MASKOUT param1 param2Parame

CONTENTS1 Introduction2Operation Notes3Features4Sender Unit Layout - Front5 Sender Unit Description6 Sender Unit Layout - Back7 Sender Unit Descript

36RS-232 SERIAL FUNCTIONS - SENDER UNIT#RMTIRADD FunctionThe #RMTIRADD function sets the IR channel for the Matrix.Syntaxy:#RMTIRADD param1Parameters:

37RS-232 SERIAL COMMANDS - SENDER UNITCommand SyntaxSimplifi ed syntax was used for command implementation for faster operation with the device. The c

38RS-232 SERIAL COMMANDS - SENDER UNITUsing parameters with the F CommandPermits disabling / enabling of +5 V for Fiber Optic Extenders.Syntaxy:f para

39RS-232 SERIAL COMMANDS - SENDER UNITR CommandThe R command allows specifi c routing of inputs and outputs when controllingthe 8x CAT6 for HDMI Sender

40RS-232 SERIAL FUNCTIONS - RECEIVER UNITFunctions SyntaxThe syntax for each function is always the same:#Character as the start fl ag → Function name

41RS-232 SERIAL FUNCTIONS - RECEIVER UNIT#EDIDMODE FunctionThe #EDIDMODEfunction sets the EDID mode.Syntaxy:#EDIDMODE param1Parameters:param1 EDID M

42RS-232 SERIAL FUNCTIONS - RECEIVER UNIT#PRLOEDID FunctionThe #PRLOEDID function reads the local EDID and spools it to the serial port.Syntaxy:#PRLOE

43RS-232 SERIAL FUNCTIONS - RECEIVER UNITGeneral FunctionsFunctionDescription#ACTIVEBOLOEnables the boot loader#BLASTERSets the blaster mode#DEEPCOLOR

44RS-232 SERIAL FUNCTIONS - RECEIVER UNIT#BLASTER FunctionThe #BLASTER function sets the Receiver Unit blaster mode.Syntaxy:#BLASTER param1 param2Para

45RS-232 SERIAL FUNCTIONS - RECEIVER UNIT#EQULIZE FunctionThe #EQULIZE function sets equalizer level on the Receiver Unit.Syntaxy:#EQULIZE param1Param

1INTRODUCTIONCongratulations on your purchase of the 8x CAT6 Extender for HDMI. Your complete satisfaction is very important to us.GefenGefen delivers

46RS-232 SERIAL FUNCTIONS - RECEIVER UNIT#HPDMODE FunctionThe #HPDMODE function sets HPD to low (OFF) or high (ON) on the HDMIinputs.Syntaxy:#HPDMODE

47RS-232 SERIAL FUNCTIONS - RECEIVER UNIT#RMTIRADD FunctionThe #RMTIRADD function sets the IR channel for the Matrix.Syntaxy:#RMTIRADD param1Parameter

48RS-232 SERIAL FUNCTIONS - RECEIVER UNIT#USERIN FunctionThe #USERIN function sets the user hardware interface.Syntaxy:#USERIN param1 param2Parameters

49RS-232 SERIAL COMMANDS - RECEIVER UNITCommand SyntaxSimplifi ed syntax was used for command implementation for faster operation with the device. The

50RS-232 SERIAL COMMANDS - RECEIVER UNITR CommandThe R command routes the Receiver Unit to a specifi c input.Syntaxy:r param1Parameters:param1 HDMI In

51IP CONTROLThe Gefen 8x CAT6 Extender for HDMI supports IP-based control using an integrated Web interface. To access this feature, an IP address, su

52IP CONTROLIP CONFIGURATIONThe IP CONFIGURATION page is used to set the IP settings that will be used toaccess the Web interface. The following items

53IP CONTROLBACKUP / RESTORETheBackup/Restore page is used to backup and restore complete setup confi gurations.Note: This feature will be implemented

54IP CONTROLPOWER MANAGEMENTThePOWER MANAGEMENTpage is used to set optional +5V power on an input to power specifi c optional devices. The current stat

55NETWORK CABLE WIRING DIAGRAMGefen recommends the TIA/EIA-568-B wiring option. Please adhere to the table below when fi eld-terminating the CAT-6 cab

READ THESE NOTES BEFORE INSTALLING OROPERATING THE 8X CAT6 EXTENDER FOR HDMI• CAT-6a cables can be used up to 200 feet (60 meters).• Shielded (STP) CA

56FIRMWARE UPDATEFirmware Update ProcedureTo begin the update procedure, the unit’s Boot Loader must be activated. To activate the Boot Loader, follow

57FIRMWARE UPDATE11. Connect the RS-232 cable to the Receiver unit.12.Repeat steps 4 - 7 and upload RHDMIDCAT6x8_e_x_x.bin.13.Repeat step 11 - 13 for

58SPECIFICATIONSVideo Amplifi er Bandwidth ... 225 MHzInput Video Signal...

59WARRANTYGefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects

60lwIP is licenced under the BSD licence:Copyright (c) 2001-2004 Swedish Institute of Computer Science.All rights reserved.Redistribution and use in s

Rev B520600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefen.com [email protected] product uses

3FEATURESSupported HDMI 1.3 Features• 225 MHz (up to 12 bit YUV 444 @ 1080p)• Deep Color• Dolby TrueHD and DTS-HD Master Audio• Lip-Sync• CEC Pass-Thr

4SENDER UNIT LAYOUT231Front

5Front1Standby ButtonSets the 8x CAT6 Extender for HDMI into Standby Mode.2 IR SensorReceives signals from the IR Remote Control.3 Power IndicatorThis