gefentv.com1080P®Wireless for HDMI Multi-Room Solution GTV-WHD-1080P-LR-BLK User Manual
PANEL LAYOUT6Sender unitFrontBack21345 6
PANEL LAYOUT7FrontBack32145 6 7Receiver unit
Sender Unit1 Pairing buttonPress and hold this recessed button using a paper clip for approximately 3 seconds to pair the Sender unit with the Receiv
9IR REMOTE CONTROL UNITLayout and Descriptions 1 MenuPress this button to display the Setup menu.2 Cursor buttonsUsed to control Left, Up, Right, and
CONNECTING THE WIRELESS FOR HDMI10How to Connect the Wireless for HDMI - Multi-Room Solution1. Connect a Hi-Def source to the Sender unit using the i
11The Linking ProcessAfter all the connections have made (see page 10) to the Wireless for HDMI, the Receiver unit will attempt to negotiate with the
Using Multiple Sender UnitsThe Wireless for HDMI can be used with up to eight Sender units to provide switching capability between Sender units. Add
4. Use the cursor buttons on the IR Remote Control to select Add new Video Source from the Setup menu.5. Press the OK button. The following message
14As the Sender unit is added to the Wireless for HDMI network, a progress bar will be displayed: After a few moments the source sig
Renaming SourcesBy default, each Sender unit is assigned the name “Sender”. This can be confusing when multiple Sender unit are used. However, this
163. The Rename Video Source Name menu will be displayed, along with the selected Source. Use the ▲ and ▼ cursor keys to change the highlighted char
174. After the video source has been renamed, press the OK button to save the changes. Select Video Source Sender BluRay SetupOPERATING THE
18Switching between SourcesOnce two or more Sender units have been connected to a Receiver unit, use the IR Remote Control unit to switch between each
193. Once the desired source has been selected, press the OK button. 4. The screen will go blank momentarily and the “Connecting to
Deleting SourcesIf a Sender unit (source) will no longer be necessary, it can be removed from the Wireless for HDMI network. 1. Point the IR Remote C
213. Click the OK button to conrm the selection.4. The Chose Source to Remote menu will be displayed.5. Select the source to be removed and press
228. Press the SOURCE button to display the Select Video Source menu. 9. Select the desired source using the cursor buttons. Then
2311. The “Connecting to...” status message will be displayed: 12. After a few moments, the selected source signal will be displayed
24Disconnecting the Wireless LinkThe Wireless for HDMI network can be completely disconnected, if necessary. This can be used in order to restrict th
25Reconnecting the Wireless Link1. Press the Source button on the IR Remote Control. The “Connecting to...” message will be displayed:
ASKING FOR ASSISTANCERev A6Technical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120 Technical Support Hours:8:00 AM to 5:00
26Power-Down ModeThe Wireless for HDMI can be powered-down when not in use. 1. Point the IR Remote Control at the Receiver unit and press the GUEST b
3. After the Wireless for HDMI has been successfully powered-down, the “Wireless Off” message will be displayed on the screen. Power
Operating Frequency... 5 GHzSupported resolutions...
WARRANTYGefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects an
Rev A620600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefentv.com [email protected] product u
CONTENTS1 Introduction2 FCC Statement3 Operation Notes5 Features6 Panel Layout6 Sender Unit7 Receiver Unit8 Panel Descriptions8 Sender Un
Congratulations on your purchase of the GefenTV Wireless for HDMI. Your complete satis-faction is very important to us. About GefenWe specialize in t
FCC STATEMENT2This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
OPERATION NOTES3READ THESE NOTES BEFORE INSTALLING OR OPERATINGTHE GEFENTV WIRELESS FOR HDMI - MULTI-ROOM SOLUTION• Maximum extension distance is 100
OPERATION NOTES4Continued from previous page » EU Models: Up to 2 pairs of Sender and Receiver units can be operated in the same environment. Local
FEATURES5HDMI Features Supported• LPCM digital audio streams up to 7.1 channels is supported• Dolby® TrueHD and DTS-HD® Master Audio™ streams up to
Commentaires sur ces manuels