gefentv.com1080P®Wireless for HDMIMulti-Room SolutionGTV-WHD-1080P-LRGTV-WHD-1080P-LR-BLKUser Manual
PANEL LAYOUT6Sender unitFrontBack213456
PANEL LAYOUT7FrontBack3214567Receiver unit
Sender Unit1 Pairing buttonPress and hold this recessed button using a paper clip for approximately 3 seconds to pair the Sender unit with the Receive
9IR REMOTE CONTROL UNITLayout and Descriptions1 MenuPress this button to display the Setup menu.2 Cursor buttonsUsed to control Left, Up, Right, and D
CONNECTING THE WIRELESS FOR HDMI10How to Connect the Wireless for HDMI - Multi-Room Solution1.Connect a Hi-Def source to the Sender unit using the inc
11The Linking ProcessAfter all the connections have made (see page 10) to the Wireless for HDMI, theReceiver unit will attempt to negotiate with the S
Using Multiple Sender UnitsThe Wireless for HDMI can be used with up to eight Sender units to provideIswitching capability between Sender units.Adding
4. Use the cursor buttons on the IR Remote Control to select Add new VideoSourcefrom the Setup menu.5. Press the OK button. The following message wil
14As the Sender unit is added to theWireless for HDMI network, a progressIbar will be displayed:After a few moments the source signal connected to the
Renaming SourcesBy default, each Sender unit is assigned the name “Sender”. This can be confusing when multiple Sender unit are used. However, this
163. The Rename Video Source Name menu will be displayed, along with the selected Source.Use the ▲ and ▼ cursor keys to change the highlighted charact
174. After the video source has been renamed, press the OK button to save thechanges.Select Video SourceSender BluRayy SetupOPERATING THE WIRELESS
18Switching between SourcesOnce two or more Sender units have been connected to a Receiver unit, use the IR Remote Control unit to switch between each
193. Once the desired source has been selected, press the OK button.4. The screen will go blank momentarily and the “Connecting to...” status messag
Deleting SourcesIf a Sender unit (source) will no longer be necessary, it can be removed from the Wireless for HDMI network.I1. Point the IR Remote C
213. Click the OK button to confi rm the selection.4.TheChose Source to Remote menu will be displayed.5. Select the source to be removed and press the
228. Press the SOURCE button to display the Select Video Source menu.9. Select the desired source using the cursor buttons. Then, press the OKbutton
2311. The “Connecting to...” status message will be displayed:12. After a few moments, the selected source signal will be displayed.Connecting to DVR.
24Disconnecting the Wireless LinkThe Wireless for HDMI network can be completely disconnected, if necessary. IThis can be used in order to restrict t
25Reconnecting the Wireless Link1.Press the Source button on the IR Remote Control. The “Connecting to...”message will be displayed:2. After a few se
ASKING FOR ASSISTANCERev A3Technical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM
26Power-Down ModeThe Wireless for HDMI can be powered-down when not in use.I1. Point the IR Remote Control at the Receiver unit and press theGUESTbut
3. After the Wireless for HDMI has been successfully powered-down, theI“Wireless Off” message will be displayed on the screen.Powering-Up after a Powe
Operating Frequency... 5 GHzSupported resolutions...
WARRANTYGefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects an
Rev A320600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefentv.com [email protected] product u
CONTENTS1 Introduction2 FCC Statement3 Operation Notes5 Features6 Panel Layout6 Sender Unit7 Receiver Unit8 Panel Descriptions8 Sender Unit8 Rec
Congratulations on your purchase of the GefenTV Wireless for HDMI. Your complete satis-faction is very important to us.About GefenWe specialize in tot
FCC STATEMENT2This device complies with part 15 of the FCCRules. Operation is subject to the following two conditions: (1) This device may not cause h
OPERATION NOTES3READ THESE NOTES BEFORE INSTALLING OR OPERATINGTHE GEFENTV WIRELESS FOR HDMI - MULTI-ROOM SOLUTION• Maximum extension distance is 100
OPERATION NOTES4Continued from previous page»EU Models: Up to 2 pairs of Sender and Receiver units can beoperated in the same environment. Local RF i
FEATURES5HDMI Features Supported•Resolutions up to 1080p Full HD• 12-bit Deep Color• Linear PCM digital audio up to 7.1 channels• Dolby® TrueHD, Dolby
Commentaires sur ces manuels